Search
Area Architetti Snaidero

TECHNICAL SPECIFICATIONS

GUIDELINES TO START DESIGNING

Creating a good kitchen requires careful and appropriate choices based on different requirements that derive from age, personality, and lifestyle.

Snaidero has two design systems: SYSTEM WITH 22 MM DOOR THICKNESS and SYSTEM WITH 19 MM DOOR THICKNESS.

SPECIFICHE PROGRAMMI 19 E 22 MM

La progettazione di una buona cucina richiede scelte attente e mirate, in risposta alle diverse esigenze dell’utente.

DOOR FINISHES AVAILABLE WITH 22 MM DOOR THICKNESS

MELAMINE

particle board support with 4 ABS edges faced with smooth or brushed matt melamine, the inside in smooth matt melamine.

LAMINATE

particle board support with 4 ABS edges faced with high gloss laminate mirror gloss finish the inside in matt melamine.

MATT LACQUER

MDF support with polyester primer, finished with matt lacquer.

HIGH GLOSS MONOLACQUER

MDF support with polyester primer faced with high gloss polyurethane lacquer finish, the inside in matt lacquer.

HIGH GLOSS LACQUER

MDF support with polyester primer, finished with high gloss polyurethane lacquer.

HIGH GLOSS METALLIZED LACQUER

MDF support with polyester primer, faced with metallized high gloss lacquer, the inside in matt lacquer.

MICALIZED LACQUER

MDF support with polyester primer and micalized matt lacquer finish, the inside in matt lacquer.

WOOD FINISHES

particle board support with 4 solid wood edges finished with different types of wood veneers.

SATIN ALUMINUM PAINTED “TOWN”

semi-transparent painted 1 mm thick aluminum on a box-type door with internal noise-reduced light structure.

FINGER-PRINT RESISTANT STAINLESS STEEL

faced with 0.8 mm thick satin stainless steel (vertical direction), the inside in wooden multi-layer, finished with anodized aluminum on the back side.

MELAMINE FRAME DOOR

Frame and center panel in particle board support with brushed melamine wood decoration. 4 ABS edges.

WOOD FRAME DOOR

Frame and center panel in particle board support with brushed and varnished wood veneer. 4 solid wooden edges.

MATT LACQUER FRAME DOOR

Frame and center panel in particle board support, melamine wrapped, with matt lacquered finish.

GENERAL CHARACTERISTICS 22 MM PROGRAM

VOID

All the base units 56 cm deep and tall units are positioned at 5.3 cm from the wall via the supplied spacers to allow the horizontal passage of any pipes, cables, etc. at a higher distance from the floor than the plinth, therefore avoiding specific housing and adjustment notches on the sides of the cabinets. The total distance between the back of the cabinets and the wall is about 9 cm. Base and tall units can also be installed at 1,3 cm from the wall by using the same metal spacers supplied in the hardware, provided that plumbing and wiring are fitted at plinth level. With this solution, the overall distance between the back of the cabinet and the wall is about 5 cm.

STRUTTURA DEL FUSTO

The carcase and the internal shelves of cabinets are made of 19 mm thick particle board panels, these panels have a very low formaldehyde emission (less than half the E1 class) covered with melamine resins to obtain high abrasion resistance and easy to clean surface. Both carcase and internal shelves feature a thick ABS front edge. The back panels of cabinets are made of HDF (High Density Fiberboard). The 19 mm thick shelves are adjustable to different height positions.

BASE AND TALL UNITS

The base and tall units are equipped with side holes to allow the perfect assembly of the various elements. They feature plastic feet mounted on external supports and allow for perfect leveling on uneven floors.

DRAWERS AND BASKETS

Drawers and pull-out baskets feature steel runners protected by epoxy paints in white (Antaro) or white and grey (Legrabox) color. Drawers and pull-out baskets are also available with stainless steel runners (Legrabox). Full-extension drawers and pull-out baskets are equipped with a softclose device. The bottom of drawers and pull-out baskets is made from a scratch-resistant melamine panel in either white or grey color.

WALL UNITS

The wall units are equipped with pre-mounted hooks that allow perfect adjustment from inside the cabinet itself. The wall mounting is made by a special steel modular guide. Two opening systems are available on wall units:

- Doors overhanging from the carcase;

- Doors flush with the carcase, with recessed bottom panel;

The latter option is available with lit metal profile as well, featuring the external light or the external and internal light.

HINGES

The quick connection hinges of the doors are metal chrome plated, they have a built-in closing spring and are equipped with a soft-closing device. They allow adjustment of the doors in three directions.

INTERNAL SHELVES

They are made in same material of the carcase, they are adjustable to different height positions.

PLINTHS

The plinths are made of : melamine-coated PVC, anodizedor painted aluminium, door finish. This model features the “floating effect” solution on base and tall units in door finish; for further information refer to the specific section “linear elements-plinths” on the common elements technical book. This model features the solution with “flush with door” plinth on base and tall units

DRAINING WALL UNIT

The draining wall unit includes a stainless steel grid. The hinged doors open at 170 degrees. The cabinet is available with a natural aluminum internal protective lining.

SINK BASE UNITS

The sink cabinet is equipped with a natural aluminum bottom lining that resists possible chemical agents and water leaks. The internal structure of sink base units can be totally lined in natural aluminum.

DOOR FINISHES AVAILABLE WITH 19 MM DOOR THICKNESS

MELAMINE

particle board support faced with matte smooth melamine, or brushed melamine, 4 ABS edges.

DOOR LACQUER WITH EDGES

MDF support faced with high gloss/matte polyurethane lacquer in different colors. The inside, in matte melamine in same color, 4 ABS edges.

GENERAL CHARACTERISTICS 19 MM PROGRAM

VOID

All the base units 56 cm deep and tall units are positioned at 5.3 cm from the wall via the supplied spacers to allow the horizontal passage of any pipes, cables, etc. at a higher distance from the floor than the plinth, therefore avoiding specific housing and adjustment notches on the sides of the cabinets. The total distance between the backs of the cabinets and the wall is about 9 cm. Base and tall units can also be installed at 1,3 cm from the wall, using the same metal spacers supplied in the hardware, provided that plumbing and wiring are fitted at plinth level. With this solution, the overall distance between the back of the cabinet and the wall is about 5 cm.

CARCASE STRUCTURE

The carcase and the internal shelves of cabinets are made of 19 mm thick particle board panels, these panels have a very low formaldehyde emission (less than half the E1 class) covered with melamine resins to obtain highabrasion resistance and easy to clean surface. Both carcase and internal shelves feature a thick ABS front edge. The back panels of cabinets are made of HDF (High Density Fiberboard). The 19 mm thick shelves are adjustable to different height positions.

DRAWERS AND BASKETS

Drawers and baskets feature steel full-extension runners protected with white epoxy paint, equipped with soft-closing system.The bottom is made of a scratch-resistant melamine panel, in white color.

BASE AND TALL UNITS

The base and tall units are equipped with side holes to allow the perfect assembly of the various elements. They feature plastic feet mounted on supports outside the cabinet and allow for perfect leveling on uneven floors.

WALL UNITS

The cabinets are equipped with pre-mounted hooks that allow perfect adjustment from inside the cabinet itself. The wall mounting is made by a special steel modular guide.

Two opening systems are available on wall units:

- Doors overhanging from the carcase;

- Doors flush with the carcase, with recessed bottom panel;

The latter option is available with lit metal profile as well, featuring the external light or the external and internal light.

HINGES

The quick release hinges of the doors are metal chrome plated, have a built-in closing spring and are equipped with a soft-closing device. They allow adjustment of the doors in three directions.

SHELVES

Shelves: are made in same material of the carcase, they are adjustable to different height positions.

PLINTHS

The plinths are made of melamine-coated PVC, aluminium or lacquered aluminium. H 10-6 cm.

DRAINING WALL UNIT

The draining wall unit a stainless steel grid. The opening of the doors is at 170 degrees.

SINK BASE UNITS

The sink base unit is equipped with a coating of aluminium at the bottom that resists chemicals and any water leaks.

 

Create your catalog

Select one of the catalogs that Snaidero has prepared for you and personalize it with your information.

The creation of the catalog can take several minutes.
Fields marked with an asterisk * are required.